A minimal composite theory for stability of non-parallel compressible boundary-layer flow

A new minimal composite theory that extends the approach of Govindarajan and Narasimha [1] is proposed here for 2D non-parallel compressible boundary-layer stability subject to 3D disturbances. The mean profiles are obtained from Hortons analysis, which provides a good approximation for a large range of Prandtl numbers at non-zero pressure gradients. In the lowest order, all effects of order lower than O(R^-2/3) anywhere in the boundary-layer are included, R being the local boundary-layer Reynolds number; the resulting non-parallel formulation yields a set of four ordinary differential equations, as compared to the five coupled equations of classical parallel flow theory of Mack [2]. The largest effect on stability of flow non-parallelism is found to be due to the wall-normal advection of velocity and temperature disturbance quantities by the mean flow. The present theory shows that the bulk viscosity, invariably included in compressible stability theories, is irrelevant at the lowest order. In comparison with the full [O(R^-1)] non-parallel theory, the present theory is marginally better than the parallel flow theory. PACS 03.50.De, 04.20-q, 42.65-k     

New exact results for the effective electric, elastic, piezoelectric and other properties of composite ellipsoid assemblages

In this paper we present a unified treatment of composite ellipsoid assemblages in the setting of uncoupled phenomena like conductivity and elasticity and coupled phenomena like thermoelectricity and piezomagnetoelectricity. The building block of this microgeometry is a confocal ellipsoidal particle consisting of a (possibly void) core and a coating. All space is filled up with such units which have different sizes but possess the same aspect ratios. The confocal ellipsoids may have the same orientation in space or may be randomly oriented. The resulting microgeometry simulates two-phase composites in which the reinforcing components are short fibers or elongated particles. Our main interest is in obtaining information of an exact nature on the effective moduli of this microgeometry whose effective tensor symmetry structure depends on the packing mode of the coated ellipsoids. This information will sometimes be complete like the full effective thermoelectric tensor of an assemblage which contains aligned ellipsoids in which the coating is isotropic and the core is arbitrarily anisotropic. In the majority of the cases however the maximum achievable exact information will be only partial and will appear in the form of certain exact relations between the effective moduli of the microgeometry. These exact relations are obtained from exact solutions for the fields in the microstructure for a certain set of loading conditions. In all the considered cases an isotropic coating can be combined with a fully arbitrary core. This covers the most important physical case of anisotropic fibers in an isotropic matrix. Allowing anisotropy in the coating requires the fulfillment of certain constraint conditions between its moduli. Even though in this case the presence of such constraint conditions may render the anisotropic coating material hypothetical, the value of the derived solutions remains since they still provide benchmark comparisons for approximate and numerical treatments. The remarkable feature of the general analysis which covers all treated uncoupled and coupled phenomena is that it is developed solely on the basis of potential solutions of the conduction problem in the same microgeometry.     

Convective Instability in Superposed Fluid and Porous Layers with Vertical Throughflow

A closed form solution to the convective instability in a composite system of fluid and porous layers with vertical throughflow is presented. The boundaries are considered to be rigid-permeable and insulating to temperature perturbations. Flow in the porous layer is governed by Darcy–Forchheimer equation and the Beavers–Joseph condition is applied at the interface between the fluid and the porous layer. In contrast to the single-layer system, it is found that destabilization due to throughflow arises, and the ratio of fluid layer thickness to porous layer thickness, , too, plays a crucial role in deciding the stability of the system depending on the Prandtl number.     

铁电薄膜在红外辐射作用下的响应

研究了红外探测器中红外焦平面列阵的象元———铁电薄膜微桥在红外辐射作用下的输出信号。用层合板壳作为微桥结构的力学模型,中间一层为压电材料,上下两层为金属材料电极。采用了力-热-电耦合的控制方程和变分原理,推导出了基于Mindlin假设的压电材料层合板有限元公式。以红外探测器在夜间从飞机上探测地面的坦克为例,用有限单元法模拟了铁电薄膜微桥在红外辐射作用下的力、热、电输出信号,并对结果作了分析比较。     

炭纤维增强环氧树脂复合材料/N80钢摩擦学性能研究

利用MG-200型摩擦磨损试验机研究了炭纤维增强环氧树脂复合材料/N80钢的摩擦学性能,考察了介质温度对摩擦学性能的影响;用扫描电子显微镜分析了磨损表面形貌.结果表明:在干摩擦条件下,炭纤维增强环氧树脂复合材料与N80钢对摩时的摩擦系数较低,炭纤维增强环氧树脂复合材料的磨损主要表现为树脂基体脱落碳化和炭纤维的折断剥落,偶件钢环则呈现明显的磨粒磨损特征;在油井产出液润滑下炭纤维增强环氧树脂复合材料的磨损率较低,摩擦系数和磨损率随着润滑介质温度的升高而增大,偶件钢环则呈现明显的磨粒磨损和腐蚀磨损特征.     

纳米金刚石对电沉积镍基复合镀层微观结构及抗磨性能的影响

利用直流电沉积技术制备了纳米和微米镍镀层,以及纳米金刚石增强镍基复合镀层,考察了纳米金刚石颗粒对纳米及微米镍基质的表面形貌、微结构、硬度及磨损性能的影响．结果表明：引入纳米金刚石使得微米镍镀层的硬度和抗磨性能显著提高;但引入纳米金刚石对纳米镍镀层硬度的影响不大,对镀层的抗磨性能则反而产生不利影响．     

油润滑条件下ZA27／SiCp复合材料的滑动磨损行为

高能超声凝固法制备ＺＡ２７／ＳｉＣｐ复合材料，用环－块摩擦磨损试验机研究了油润滑下复合材料的滑动摩擦磨损性能，发现未增强的基体合金在重载时产生严重粘着磨损，磨损层发生软化和塑性流动，而复合性能中的ＳｉＣ颗粒暴露于磨损表面并起承载作用，从而保护基体不发生严重磨损。与基体合金相比，复合材料的摩擦系数平稳而较低，且耐磨性提高１０倍以上。     

Strain analysis for moiré interferometry using the two-dimensional continuous wavelet transform

In this paper, we introduce the two-dimensional continuous wavelet transform for the automated strain analysis of the moiré interference fringe pattern. The Fourier transform method has been widely used for automated analysis of an optical interference fringe pattern. However, this method is hardly applicable to the analysis of the fringe pattern, which includes large displacement range or discontinuities. We show the advantages of the wavelet transform method by applying it to experimental results on composite laminates.     

A Binary Model of textile composites: III high failure strain and work of fracture in 3D weaves

Prior experiments have revealed exceptionally high values of the work of fracture (0.4-) in carbon/epoxy 3D interlock woven composites. Detailed destructive examination of specimens suggested that much of the work of fracture arose when the specimens were strained well beyond the failure of individual tows yet still carried loads . A mechanism of lockup amongst broken tows sliding across the final tensile fracture surface was suggested as the means by which high loads could still be transferred after tow failure. In this paper, the roles of weave architecture and the distribution of flaws in the mechanics of tow lockup are investigated by Monte Carlo simulations using the so-called Binary Model. The Binary Model was introduced previously as a finite element formulation specialised to the problem of simulating relatively large, three-dimensional segments of textile composites, without any assumption of periodicity or other symmetry, while preserving the architecture and topology of the tow arrangement. The simulations succeed in reproducing all qualitative aspects of measured stress-strain curves. They reveal that lockup can indeed account for high loads being sustained beyond tow failure, provided flaws in tows have certain spatial distributions. The importance of the interlock architecture in enhancing friction by holding asperities on sliding fibre tows into firm contact is highlighted.     

ELECTROELASTIC FIELD FOR AN IMPERMEABLE ANTI-PLANE SHEAR CRACK IN A PIEZOELECTRIC CERAMICS PLATE

ＩｎｔｒｏｄｕｃｔｉｏｎＤｕｅｔｏｔｈｅｉｎｔｒｉｎｓｉｃｃｏｕｐｌｉｎｇｃｈａｒａｃｔｅｒｉｓｔｉｃｓｂｅｔｗｅｅｎｅｌｅｃｔｒｉｃａｎｄｅｌａｓｔｉｃｂｅｈａｖｉｏｒｓ,ｔｈａｔｉｓ,ａｐｐｌｉｅｄｍｅｃｈａｎｉｃａｌｌｏａｄｉｎｇｐｒｏｄｕｃｅｓｅｌａｓｔｉｃｄｅｆｏｒｍａｔｉｏｎ ,ａｓｗｅｌｌａｓｅｌｅｃｔｒｉｃｆｉｅｌｄ ,ａｎｄｃｏｎｖｅｒｓｅｌｙｅｌｅｃｔｒｉｃｆｉｅｌｄｃａｎｇｉｖｅｒｉｓｅｔｏｅｌａｓｔｉｃｄｅｆｏｒｍａｔｉｏｎ ,ｐｉｅｚｏｅｌｅｃｔｒｉｃｍａｔｅｒｉａｌｓｈａｖｅ…